Search Results

Dynamic and economic performance play an important role in the vehicle evaluation indexes, and also are crucial parts considered during the design progress. This paper applies a method of parameters matching of powertrain to one Pure Electric City Bus(PECB), with which a four-speed transmission dynamic system is designed. Meanwhile two powertrain models adopting motors with identical peak power but different base speeds and peak torques coupled with two-speed transmission or without transmission are introduced for comparison to analyze if a smaller motor performs better in performance. The three models are based on identical type of bus. Then according to the powertrain parameters, simulation models of three bus models are established respectively. From the results of simulation, vehicle performances of the four-speed transmission powertrain, especially economic performance, are compared with the other two.

At present, many electric vehicles are often equipped with only a single-stage final drive. Although the single-stage speed ratio can meet the general driving requirements of electric vehicles, if the requirements of the maximum speed and the requirements for starting acceleration or climbing are met at the same time, the power demand of the drive motor is relatively large, and the efficient area of the drive motor may be far away from the operating area corresponding to daily driving. If the two-speed automatic transmission is adopted, the vehicle can meet the requirements of maximum speed, starting acceleration and climbing at the same time, reduce the power demand of the driving motor, and improve the economy under certain power performance. This is especially important for medium and large vehicles.

The plug-in hybrid electric vehicle (PHEV) gradually moves into the mainstream market with its excellent power and energy consumption control, and has become the research target of many researchers. The energy management strategy of plug-in hybrid vehicles is more complicated than conventional gasoline vehicles. Therefore, there are still many problems to be solved in terms of power source distribution and energy saving and emission reduction. This research proposes a new solution and realizes it through simulation optimization, which improves the energy consumption and emission problems of PHEV to a certain extent. First, on the basis that MATLAB software has completed the modeling of the key components of the vehicle, the fuzzy controller of the vehicle is established considering the principle of the joint control of the engine and the electric motor.

With the shortage of energy and the continuous development of automotive technology, electric vehicles are gradually gaining popularity. The energy of electric vehicles mainly comes from the power grid, and its large-scale use is inseparable from the support of the power system. However, electric vehicles consume power quickly, have short driving ranges, and frequently charge, and there are plenty of problems such as disorder and randomness in charging, which is not conducive to rational planning of the power grid. Optimizing the charging problem of electric vehicles can not only save power resources but also bring huge economic benefits to operators of charging stations. In this paper, the CAN bus communication protocol, combined with GPS positioning, LabVIEW monitoring, GPRS transmitting and other technical means, can realize the information exchange of the "vehicle-charging device-distribution network".

In order to study the influence of low-viscosity oil on automobile pollutant emissions reduction, three different 0W20 oil samples were prepared with oil 5W30 as the base oil. Parameters such as the oil viscosity, ash, and element content were tested at different stages, speeds, and accelerations of the Worldwide Harmonized Light Vehicles Test Cycle (WLTC). The results showed the effects of low-viscosity oil on exhaust emissions reduction were mainly concentrated in the low-speed and extra high-speed segment. At the low-speed segment, especially in the starting stage, carbon monoxide (CO), total hydrocarbon (THC), and non-methane hydrocarbon (NMHC) emissions can be reduced. The use of low ash oil can reduce nitrogen oxides (NOx) emissions; the methane (CH4) emissions can be reduced by increasing the Zinc (Zn) content in engine oil moderately.

For vehicle thermoelectric generator, heat would be directly transferred into electricity by thermoelectric modules because there was temperature difference between heat exchanger and water tank. The electrical power generation was deeply influenced by temperature difference, temperature uniformity and topological structure of TEG. In previous works, increasing the difference of temperature would significantly enhance the power generation of TEG and inserted fins were always applied to enhance heat transfer in parallel-plate heat exchanger. But fins would result in a large backpressure which was not conductive to efficiency of the engine.In current study, to enhance heat transfer rates and outside surface temperature, cylindrical grooves on the top and bottom surface in heat exchanger was proposed. The cylindrical grooves could increase the heat transfer area and enhance the turbulence intensity, meanwhile there was no inserts in the fluid to block the flow.

Blade Electric Vehicle (BEV) with a light body plays an important role in saving the energy and reducing the exhaust emission. However, reducing the body weight need to meet the heterogeneous attributes such as structural, safety and NVH (Noise, Vibration and Harshness) performance. With the rapid development of finite element (FE) analysis technology, simulation analysis is widely used for researching the complex engineering design problem. Multidisciplinary Design Optimization (MDO) of a BEV body is a challenging but meaningful task in the automotive lightweight. In present research, the MDO is introduced to optimize a BEV Body-in-White (BIW).

The heavy duty trucks have large engine power and drive continuously in mountainous area, so the heat dissipation of engine is very important. In the traditional cooling system with fixed transmission ratio fan, the cooling capacity is insufficient and the engine is easy to be over-heated when the engine is working in low speed and heavy load conditions. Owning to the bigger size of electric motor compared to the hydraulic motor, it is not suitably applied to the heavy duty trucks. Contrasted with the electric motor, the hydraulic drive cooling system is widely applied in heavy duty trucks due to smaller size, larger power, continuous speed modulation and flexible installation location. However, the low transmission efficiency of the pump-motor system results in high power consumption of the cooling system. In this paper, the mathematical and simulation model of hydraulic-driven fan cooling system is established for the specific engine.

In this paper a new pressure control method of a modified accumulator-type Electro-hydraulic Braking System (EHB) is proposed. The system is composed of a hydraulic motor pump, an accumulator, an integrated master cylinder, a pedal feel simulator, valves and pipelines. Two pressurizing modes are switched between by-motor and by-accumulator to adapt different pressure boost demands. A differentiator filtering raw sensor signal and calculating pedal speed is designed. By using the pedal feel simulator, the relationship between wheel pressures and brake force is decoupled. The relationships among pedal displacement, pedal force and wheel pressure are calibrated by experiments. A model-based PI controller with predictor is designed to lower the influences caused by delay. Moreover, a self-tuning regulator is introduced to deal with the parameter’s time-varying caused by temperature, brake pads wearing and delay variation.

For the thin ice on the road in winter, the traditional road deicing vehicle relies on mechanical and chemical methods for melting ice, which is inclined to damage the pavement and has insidious influence on environment. The thermal deicing vehicle has been adopted in recent years. Although the deicing method is available, the deicing efficiency is unacceptable while the energy consumption is huge. The study adopts the new idea of “bottom-to-top” for melting the intersection area between the road surface and the bottom ice layer by the microwave heating firstly and then cleaning them out using high pres. vapor cutting so as to save the cost of energy and enhance the traffic safety. First of all, the mathematical model of the melting process of the intersection of the pavement and the ice layer was established according to the microwave heating characteristics.

Heat generated by friction between the brake discs and the brake pad causes the disc temperature to rise, which affects the braking performance. This flux generated from the contact surface of the vehicle brake disc not only affects the braking performance but also tends to be wasted and pollutes the environment. However, an accurate system is needed to make efficient use of this generated heat flux, which is usually wasted. Thermoelectric generators (TEGs) are solid-state gadgets utilized in the conversion of heat to electricity. Hence, the aim of this study is to convert the heat flux generated at the disc contact surface into electrical energy by employing a thermoelectric generator. In Addition, the energy harvested energy to power the battery, which in turn charges the temperature monitoring systems. Thermoelectric generators were positioned at different geometrical points of the brake discs to achieve optimal efficiency and energy storage possibilities.

Knowledge about the health conditions and expected lifetime of an operating fuel cell stack is essential to system control and maintenance of a fuel cell vehicle. To quickly and accurately estimate a stack’s lifetime, a data-driven prediction model for proton exchange membrane fuel cells (PEMFCs) is proposed in this study. In this model, the voltage output of the fuel cell stack is taken as the lifetime evaluation index. Two methods are used to establish the lifetime decay evaluation criteria of the PEMFC stack, i.e., (1) Least Squares Fitting (LSF) method that establishes the standard for stack voltage degradation behavior, and (2) Back Propagation (BP) neural network that learns the stack’s voltage decay characteristics and establishes the standard for the stack’s voltage degradation behavior. The Autoregressive Moving Average (ARMA) time series model is then employed to learn part of the known decay behavior of stack voltage so as to predict future stack decay.

How to improve the measurement accuracy of road gradient is the key content of the research on the speed warning of commercial vehicles in mountainous roads. The large error of the measurement causes a significant effect of the vehicle speed threshold, which causes a risk to the vehicle's safety. Conventional measuring instruments such as accelerometers and gyroscopes generally have noise fluctuation interference or time accumulation error, resulting in large measurement errors. To solve this problem, the Kalman filter method is used to reduce the interference of unwanted signals, thereby improving the accuracy of the slope measurement. However, the Kalman filtering method is limited by the estimation error of various parameters, and the filtering effect is difficult to meet the project research requirements.

The paper analyzes the technological features of hydrogen fuel cell vehicles, describes the changes that hydrogen fuel cell vehicles will bring to the automobile industry and the marketing modes, and proposes a brand-new marketing mode of “automobile supermarket”. It also introduces the opportunities and challenges that fuel cell technology will bring to the world energy technology, and puts forward a concept of “hydrogen energy network” to push the mutual development of both hydrogen fuel cell vehicles and hydrogen energy industry.

In this research, the Mg2Si1-xSnx thermoelectric material is used in the exhaust temperature difference power-generating system, and the material's heat transfer characteristic and power-generating characteristic were analyzed. Firstly, steady heat transfer model from vehicle exhaust to cooling water was established. Then the impact of Sn/Si ratio to the thermoelectric characteristic parameter was analyzed. Finally, considering the influence of varying thermal conductivity to the heat transfer process along the material's heat transfer direction, when the cold end temperature of thermoelectric materials was controlled by cooling water respectively boiling at 343K and 373K, the thermoelectric conversion efficiency and power output of Mg2Si1-xSnx thermoelectric materials with different x value were evaluated based on simulation calculation.

The drivers' hysteretic perception to surrounding environment will affect vehicular fuel economy, especially for the heavy-duty vehicles driving under complex conditions and long distance in mountainous areas. Unreasonable acceleration or deceleration on the slope will increase the fuel consumption. Improving the performance of the engine and the transmission system has limited energy saving potential, and most fuel-efficient driving assistant systems don't consider the road conditions. The main purpose of this research is to introduce an economic driving scheme with consideration of the prestored slope information in which the vehicle speed in mountainous slopes is reasonably planned to guide the driver's behavior for reduction of the fuel consumption. Economic driving optimization algorithm with low space dimension and fast computation speed is established to plan accurate and real-time economic driving scheme.

To face the challenges of fossil fuel shortage and air pollution problems, there is growing interest in the potential usage of alternative fuels such as bio-ethanol and bio-butanol in internal combustion engines. The literature shows that the acetone in the Acetone-Butanol-Ethanol (ABE) blends plays an important part in improving the combustion performance and emissions, owing to its higher volatility. In order to study the effects of acetone addition into commercial gasoline, this study focuses on the differences in combustion, performance and emission characteristics of a port-injection spark-ignition engine fueled with pure gasoline (G100), ethanol-containing gasoline (E30) and acetone-ethanol-gasoline blends (AE30 at A:E volumetric ratio of 3:1). The tests were conducted at 1200RPM with the default calibration (for gasoline), at 3 bar and 5 bar BMEP under various equivalence ratios.

The hydraulic retarder is an important auxiliary braking device. With merits such as its high braking torque, smooth braking, low noise, long service life and small size, it is widely used on modern commercial vehicles. Transmission fluid of traditional hydraulic retarder is cooled by engine cooling system, which exhausts the heat directly and need additional energy consumption for the thermal management component. On account of the working characteristics of hydraulic retarder, this study designs a set of waste heat recovery system based on the Organic Rankine Cycle (ORC). Under the premise of ensuring stable performance of hydraulic retarder, waste heat energy in transmission fluid is recycled to supplement energy requirements for cooling system. First of all, a principle model, which is scaled down according to D300 retarder`s thermal power generation ration of 1:100, is established. Then through theoretical calculations, components' structural parameters of the ORC are determined.

Good braking performance is an important guarantee for the vehicle driving. In the condition of frequent or prolonged braking, the overheating problem for the traditional mechanical braking device causes the recession of the braking performance, which is a prominent problem especially for the commercial vehicle perennial traveling in the mountains. Eddy current retarder can reduce the mechanical brake load as a kind of auxiliary braking device. Thus, the temperature of the mechanical braking device would not be too high, and the traveling safety of the vehicle can be ensured. But eddy current retarder would cause an enormous impact for automobile battery when it starts up and huge electricity energy would be consumed which means that more automotive batteries are needed. Considering above, a kind of self-excited eddy current retarder is developed in the paper.

In the Rankine cycle, the pressure differential generated by the phase change of the working fluid produces turbine output power, which enables the recovery of waste heat from the internal combustion engine. The heat transfer ability of the evaporator is the key factor that determines the quality of turbine's mechanical work. In this paper, the performance of the evaporator with two-phase zone and preheated zone is studied. After obtaining the thermal characteristics of diesel engine exhaust from the experimental data, the mathematical model of the evaporator is built according to the specific working conditions of ORC and geometrical parameters of the evaporator. Three typical engine operating conditions are used to estimate the heat transfer characteristics of the evaporator. The result shows that, in the evaporator, the heat transfer coefficient of the Rankine working fluid is much greater than the exhaust side of the engine.